Author: Webmaster

[et_pb_section fb_built="1" _builder_version="4.4.0"][et_pb_row _builder_version="4.4.0"][et_pb_column type="4_4" _builder_version="4.4.0"][et_pb_text _builder_version="4.4.0"]

The Eq6 is fixed to the pier/tripod using a central bolt, but this generates significant friction between the tripod/pier and EQ6 which can make polar alignment along the azimuth axis difficult, you need the central bolt to be tight to ensure no movement but loose to adjust the azimuth for polar alignment, but it can't be both, fortunately this can be easily fixed.

If you haven't done it already complete the knobs mod.

Parts:

• 200mm x 200mm 1mm thick PTFE sheet

Instructions:

I used 1mm thick PTFE sheet, but I know others who have had success with thinner PTFE sheet, you can cut this using sturdy scissors, but I opted to scribe the PTFE using a pair of engineering dividers. Simply place the sheet between the mount and the pier adapter/tripod.

Note image below doesn't show the hole you have to cut for the lug that protrudes from the pier/tripod which the  azimuth adjustment bolts push against.

[/et_pb_text][et_pb_text admin_label="Image" _builder_version="4.4.0"]

[caption id="" align="aligncenter" width="800"] PTFE between the pier mount and the EQ6 make for super smooth azimuth adjustment when polar aligning the mount[/caption]

[/et_pb_text][/et_pb_column][/et_pb_row][/et_pb_section]

[et_pb_section fb_built="1" _builder_version="4.4.0"][et_pb_row _builder_version="4.4.0"][et_pb_column type="4_4" _builder_version="4.4.0"][et_pb_text _builder_version="4.4.0" hover_enabled="0"]

The polar adjustment knobs on the EQ6 are not very good, upgrading these parts will make your telescope mount much easier to use and therefore will result in better polar alignment leading to better images. 

The problems:

• The Azimuth adjustment knobs are too small to get a good grip on them
• The Azimuth adjustment knobs are too close to the mount, so you either bang your knuckles into the mount or can't get a propper grip on the knobs.
• The Altitude adjustment bolts are too soft and bend easily
• The handles on the Altitude adjustment bolts are too small and uncomfortable to handle.

The Solution:

Fortunately these problems can be fixed relatively easily by replacing the parts.

Parts list:

• 80mm, M10 clamping knobs with 50mm star shaped knob
• 80mm, M10 machine knobs with adjustable metal handles

Tips:

This is a straightforward modification, but there are a few things to consider.

1. When removing the altitude adjustment bolts remove the telescope and counter weights, also be careful that the mount doesn't swing down - the mount is heavier that you think so this job is best done on a workbench with the mount laying on its side.
2. If you can't remove the rear (south facing) altitude adjustment bolt - don't force it, you will damage the thread -  it is probably bent! this is a common problem with the EQ6. Unfortunately fixing it, although straight forward, does require removing the circular caps and unbolting the the central altitude bearing bolt and almost everyone who tries this damages the end caps covering the altitude bearing bolt. These caps are glued in place with what looks like epoxy. I was lucky and the paint the expoy was glued to gave way but it is very unusual for these to not be destroyed in the process of removing them (if you do destroy them you can get replacements from Modern Astronomy as part of their slide mod). 

[/et_pb_text][et_pb_text admin_label="Image" _builder_version="4.4.0"]

Replacement Knobs for the EQ6 make a huge difference to polar alignment

[/et_pb_text][et_pb_text admin_label="Bent Alt bolt Image" _builder_version="4.4.0"]

[/et_pb_text][et_pb_text _builder_version="4.4.0" hover_enabled="0"]

If you haven't done it already also do the super smooth azimuth mod and the super smooth Altitude mod. 

[/et_pb_text][/et_pb_column][/et_pb_row][/et_pb_section]